1. Загрузите и разархивируйте файл с здесь.
2. Загрузите последнюю версию прошивки с официальный сайт и переименуйте его в Recovery.bin.
3. Выключите маршрутизатор. Отключите адаптер питания или нажмите кнопку ПИТАНИЕ.
4. Подключите компьютер к порту LAN маршрутизатора с помощью кабеля Ethernet.
5. Настройте IP-адрес вашего компьютера как «192.168.1.88» вручную.
6. Запустите «tftp32.exe».
7. Запустите «netsh advfirewall set allprofiles state off» в командной строке, чтобы отключить брандмауэр Windows, в противном случае tftp будет заблокирован.
8. Нажмите кнопку/отверстие «Сброс» и удерживайте ее. Прежде чем маршрутизатор включится и до того, как tftp начнет загрузку прошивки, не отпускайте кнопку/отверстие «Сброс».
9. Включите маршрутизатор.
10. Когда все индикаторы начнут быстро мигать или когда tftp начнет загрузку прошивки, вы можете отпустить кнопку/отверстие «Сброс».
11. Когда индикатор начнет медленно мигать, обновление завершено.
12. Пожалуйста, восстановите IP-адрес вашего компьютера на динамический IP-адрес.
13. Готово.
Комментариев: 10
@Alexander
Dear Customer,
Yes, you are right.
“OK, answer this myself (for TR3000 v1.0):
1. Find and download tftp32.exe
2. make directory “tftpboot”
3. put tftp32.exe AND the firmware (renamed to “recovery.bin”) into that directory
4. connect your PC to the LAN-port of the device
5. set your LAN IP to 192.168.1.88 like described here.
6. disable windows firewall (can do this with click and point in windows)
7. start tftp from the directory in step 2. and leave that window open
8. press reset-button on the device and then connect it to power/power on, keep pressed and wait, until it starts blinking/downloading the firmware to the device (in my case this was done after 3 seconds)
9. Enable firewall again, enable dynamic config (DHCP) on your lan port again, re-connect your lan and start to configure your Cudy device”
OK, answer this myself (for TR3000 v1.0):
1. Find and download tftp32.exe
2. make directory “tftpboot”
3. put tftp32.exe AND the firmware (renamed to “recovery.bin”) into that directory
4. connect your PC to the LAN-port of the device
5. set your LAN IP to 192.168.1.88 like described here.
6. disable windows firewall (can do this with click and point in windows)
7. start tftp from the directory in step 2. and leave that window open
8. press reset-button on the device and then connect it to power/power on, keep pressed and wait, until it starts blinking/downloading the firmware to the device (in my case this was done after 3 seconds)
9. Enable firewall again, enable dynamic config (DHCP) on your lan port again, re-connect your lan and start to configure your Cudy device
Sadly this does not work with my TR3000:
1. The download link (for tftp32?) is broken/does not work.
2. It doesn’t say where to put the sysupgrade firmware after download.
3. Does the sysupgrade firmware have to be renamed (to “recovery.bin”)?
Actually the stock vendor firmware for me is better/easier than open-wrt. So it should be possible to reflash to stock fw.
@Chris,
Thank you for you help. I have sent the method “connect to the WAN port” to Ivan.
“Hi Team, I can answer myself; got it running to flash back to Cudy FW for a TR1200 by connecting to the WAN (!) Port on Cudy; not the LAN port. That was the only thing different for TR1200 compared to the the description above”Hi Team, I can answer myself; got it running to flash back to Cudy FW for a TR1200 by connecting to the WAN (!) Port on Cudy; not the LAN port. That was the only thing different for TR1200 compared to the the description above