Что такое режим точки доступа?
Режим точки доступа — маршрутизатор использует проводное соединение с основным маршрутизатором или модемом-маршрутизатором для расширения зоны покрытия беспроводной сети домашней сети. .
Общая топология сети:
Шаг 1. Откройте веб-браузер и перейдите по адресу http://cudy.net или http://192.168.10.1.
Подробную информацию см. в разделе Как войти в веб-интерфейс. Cudy Router?
Шаг 2. Появится окно быстрой настройки, выберите «Точка беспроводного доступа», затем нажмите «Далее» .
Шаг 3. Выберите свой «часовой пояс».
Шаг 4. Подтвердите подключение оборудования.
Шаг 5. Измените имя и пароль беспроводной сети.
Шаг 6. Нажмите «Сохранить и применить», чтобы завершить настройку.
Шаг 7. Подождите несколько секунд, пока система перезагрузится. Когда снова появится страница входа в систему, вы сможете пользоваться Интернетом.
Примечание.
После настройки маршрутизатора Cudy в режим точки доступа IP-адрес будет назначен хост-маршрутизатором, а IP-адрес по умолчанию 192.168.10.1 не позволит войти в систему. Если вам необходимо войти в маршрутизатор Cudy еще раз введите «http://cudy.net' в браузер или найдите IP-адрес маршрутизатора Cudy в клиенте основного (основного) маршрутизатора. список.
Комментариев: 28
Hi, I have installed a Cudy 1300 Outdoor AP on a clients site, did the complete setup and as a wireless access point. I had set static ip address for the AP but werent internet connection through the AP, I then changed the AP’s ip setting to dhcp. On the status page it shows that the AP is connected to the internet via the lan cable but when I connect my laptop other device to the wifi its not getting internet access. Also cannot pin the gateway ip address from my laptop, but on the diagnostics page of the ap I can ping the gateway ip address. Can you please help with this, as I have a wireless camera connected to this AP but cannot access it from my lan.
@Steve,
Dear Customer,
Thank you for contacting Cudy support team. Please follow the steps:
1. Set the LAN IP address to the same subnet of the main router, it will be easy to login to the web page.
2. Set the WiFi SSID and password as you want.
3. Disable the DHCP server of the P5.
Then you can connect to the main router and use it as a AP.
“I have configured my P5 router, now I’d like to change it to Access Point. I can not see in the web interface any references at all to operation mode. How do I change the operation mode from wireless router to Access Point router?”
@Rafal,
Dear Customer,
Thank you for contacting Cudy support team.
Our technical support has sent you the solutions via email. Please check.
“Hi. I have an LT500 router upstairs with sim card and another downstairs connected in AP mode via ethernet cable to the 1st one due there is very little wifi signal coming between floors through the ceiling. It works well but results in 2 different wifi networks upstairs and downstairs. So when moving between rooms devices not always switch to the network with better signal. How to make it one network with same login and password on both floors? Is it possible to configure a mesh in this situation?”
I have configured my P5 router, now I’d like to change it to Access Point. I can not see in the web interface any references at all to operation mode. How do I change the operation mode from wireless router to Access Point router?
Hi. I have an LT500 router upstairs with sim card and another downstairs connected in AP mode via ethernet cable to the 1st one due there is very little wifi signal coming between floors through the ceiling. It works well but results in 2 different wifi networks upstairs and downstairs. So when moving between rooms devices not always switch to the network with better signal. How to make it one network with same login and password on both floors? Is it possible to configure a mesh in this situation?