1.從 這裡。
2.從 官方網站並將其重新命名為"recovery.bin"。
3.關閉路由器電源。拔掉電源供應器或按電源按鈕。
4.使用乙太網路線將電腦連接到路由器的 LAN 連接埠。
5.手動將電腦的 IP 位址配置為"192.168.1.88"。 6.執行"tftp32.exe"。
7.在命令列中執行"netsh advfirewall set allprofiles state off"來停用Windows防火牆，否則tftp將被阻止。
8.按下"重設"按鈕/孔並按住。在路由器開機和 tftp 開始下載韌體之前，請勿放開"重設"按鈕/孔。 9.開啟路由器電源。 10。當指示燈全部快速閃爍時，或 tftp 開始下載韌體時，您可以放開"重設"按鈕/孔。
11.當燈慢閃時，升級完成。
12.請將您電腦的IP位址還原為動態IP。 13.完成。
10 則留言
@Alexander
Dear Customer,
Yes, you are right.
“OK, answer this myself (for TR3000 v1.0):
1. Find and download tftp32.exe
2. make directory “tftpboot”
3. put tftp32.exe AND the firmware (renamed to “recovery.bin”) into that directory
4. connect your PC to the LAN-port of the device
5. set your LAN IP to 192.168.1.88 like described here.
6. disable windows firewall (can do this with click and point in windows)
7. start tftp from the directory in step 2. and leave that window open
8. press reset-button on the device and then connect it to power/power on, keep pressed and wait, until it starts blinking/downloading the firmware to the device (in my case this was done after 3 seconds)
9. Enable firewall again, enable dynamic config (DHCP) on your lan port again, re-connect your lan and start to configure your Cudy device”
OK, answer this myself (for TR3000 v1.0):
1. Find and download tftp32.exe
2. make directory “tftpboot”
3. put tftp32.exe AND the firmware (renamed to “recovery.bin”) into that directory
4. connect your PC to the LAN-port of the device
5. set your LAN IP to 192.168.1.88 like described here.
6. disable windows firewall (can do this with click and point in windows)
7. start tftp from the directory in step 2. and leave that window open
8. press reset-button on the device and then connect it to power/power on, keep pressed and wait, until it starts blinking/downloading the firmware to the device (in my case this was done after 3 seconds)
9. Enable firewall again, enable dynamic config (DHCP) on your lan port again, re-connect your lan and start to configure your Cudy device
Sadly this does not work with my TR3000:
1. The download link (for tftp32?) is broken/does not work.
2. It doesn’t say where to put the sysupgrade firmware after download.
3. Does the sysupgrade firmware have to be renamed (to “recovery.bin”)?
Actually the stock vendor firmware for me is better/easier than open-wrt. So it should be possible to reflash to stock fw.
@Chris,
Thank you for you help. I have sent the method “connect to the WAN port” to Ivan.
“Hi Team, I can answer myself; got it running to flash back to Cudy FW for a TR1200 by connecting to the WAN (!) Port on Cudy; not the LAN port. That was the only thing different for TR1200 compared to the the description above”Hi Team, I can answer myself; got it running to flash back to Cudy FW for a TR1200 by connecting to the WAN (!) Port on Cudy; not the LAN port. That was the only thing different for TR1200 compared to the the description above