Che cos'è la modalità punto di accesso?
La modalità Access Point indica che il router utilizza una connessione cablata al router principale o al modem router per espandere la copertura wireless per una rete domestica .
Topologia di rete comune:
Passaggio 1: apri un browser web e vai su http://cudy.net o http://192.168.10.1.
Per i dettagli, fare riferimento a Come accedere all'interfaccia web di Cudy Router?
Passaggio 2: verrà visualizzata la finestra Configurazione rapida, scegli "Punto di accesso wireless", quindi fai clic su "Avanti" .
Passaggio 3: scegli il tuo "fuso orario".
Passaggio 4: conferma la connessione hardware.
Passaggio 5: cambia il nome e la password della rete wireless.
Passaggio 6: fai clic su "Salva e applica" per completare la configurazione.
Passaggio 7: attendi qualche secondo per il riavvio del sistema, quando viene nuovamente visualizzata la pagina di accesso, puoi goderti Internet.
Nota:
Dopo aver configurato il router Cudy in modalità Access Point, l'indirizzo IP verrà assegnato dal router host e l'indirizzo IP predefinito 192.168.10.1 non sarà in grado di accedere. Se è necessario accedere al router Cudy di nuovo, digita 'http://cudy.net' nel tuo browser o cerca l'indirizzo IP del router Cudy nel client del router principale (primario) elenco.
26 commenti
@Daouda
Cher Daouda,
Veuillez suivre les étapes suivantes :
1. Connectez-vous à la page web de Cudy. Définissez l’adresse IP LAN sur une adresse IP statique. Par exemple, si l’adresse IP LAN de Mikrotik est 192.168.1.1, vous pouvez configurer Cudy sur 192.168.1.254, masque 255.255.255.0, passerelle 192.168.1.1 et DNS 192.168.1.1.
2. Désactivez le serveur DHCP de Cudy.
Vérifiez ensuite si le problème est résolu ?
“Bonsoir a tous , j’espère que vous vous portez bien.
Au fait j’ai configuré mon antenne Cudy AC 1200 en mode point d’accès sans fil. Au début ça fonctionnait correctement, mais après une journée de fonctionnement, lorsque les clients essaie de se connecter, le portail captif de mon mikrotik au quel est connecté l’antenne ne s’affiche pas. Ç’est ma deuxième antenne qui fonctionne de cette manière. Vraiment j’ai besoin d’aide.”
Bonsoir a tous , j’espère que vous vous portez bien.
Au fait j’ai configuré mon antenne Cudy AC 1200 en mode point d’accès sans fil. Au début ça fonctionnait correctement, mais après une journée de fonctionnement, lorsque les clients essaie de se connecter, le portail captif de mon mikrotik au quel est connecté l’antenne ne s’affiche pas. Ç’est ma deuxième antenne qui fonctionne de cette manière. Vraiment j’ai besoin d’aide.
@Werner
Dear Customer，
Thank you for contacting Cudy support team.
Please set the AP to static IP address, then reboot the main router, and check again.
“Hi, I have installed a Cudy 1300 Outdoor AP on a clients site, did the complete setup and as a wireless access point. I had set static ip address for the AP but werent internet connection through the AP, I then changed the AP’s ip setting to dhcp. On the status page it shows that the AP is connected to the internet via the lan cable but when I connect my laptop other device to the wifi its not getting internet access. Also cannot pin the gateway ip address from my laptop, but on the diagnostics page of the ap I can ping the gateway ip address. Can you please help with this, as I have a wireless camera connected to this AP but cannot access it from my lan.”
Hi, I have installed a Cudy 1300 Outdoor AP on a clients site, did the complete setup and as a wireless access point. I had set static ip address for the AP but werent internet connection through the AP, I then changed the AP’s ip setting to dhcp. On the status page it shows that the AP is connected to the internet via the lan cable but when I connect my laptop other device to the wifi its not getting internet access. Also cannot pin the gateway ip address from my laptop, but on the diagnostics page of the ap I can ping the gateway ip address. Can you please help with this, as I have a wireless camera connected to this AP but cannot access it from my lan.
@Steve,
Dear Customer,
Thank you for contacting Cudy support team. Please follow the steps:
1. Set the LAN IP address to the same subnet of the main router, it will be easy to login to the web page.
2. Set the WiFi SSID and password as you want.
3. Disable the DHCP server of the P5.
Then you can connect to the main router and use it as a AP.
“I have configured my P5 router, now I’d like to change it to Access Point. I can not see in the web interface any references at all to operation mode. How do I change the operation mode from wireless router to Access Point router?”